Difference between revisions of "Engine: Vacuum Hose Reduction"

From 3000GT/Stealth Wiki
Jump to navigation Jump to search
(Created page with "Category:How To Category:Engine ''The core of this instruction was copied from a 12/29/2006 thread by Struggly'' This thread explains the vacuum hose reduction for th...")
 
(Complete revamp of guide structure, added broken images and additional information.)
Line 1: Line 1:
 
[[Category:How To]]
 
[[Category:How To]]
 
[[Category:Engine]]
 
[[Category:Engine]]
''The core of this instruction was copied from a 12/29/2006 thread by Struggly''
 
  
This thread explains the vacuum hose reduction for the 1G Federal (’91-93, 1G California (’91-93), and 2G Hybrid ECU (’94-95) cars. Below are brief descriptions of the systems involved, a list of tools required to perform the modification, and step-by-step instructions for the modification itself. It is intended to be a general guide only; hose reductions will vary according to individual setups and preferences.  
+
= How to Perform a Vacuum Hose Reduction on a Mitsubishi 3000GT / Dodge Stealth =
 +
<div style="float:right;margin-left: 20px;margin-bottom: 20px;">__TOC__</div>
 +
 
 +
This guides explains the '''vacuum hose reduction for the first generation 1991-1993 Mitsubishi 3000GT and Dodge Stealth'''; specifically the Federal Spec ’91-93, California Spec ’91-93, and 2G Hybrid ECU ’94-95 cars. Below are brief descriptions of the systems involved, a list of tools required to perform the modification, and step-by-step instructions for the modification itself. It is intended to be a general guide only; hose reductions will vary according to individual setups and preferences.  
  
 
Throughout the writeup I will refer to sources of boost pressure and vacuum. Vaccum conditions exist only after the throttle body. Boost pressure conditions exist only after the turbochargers. Pressure before the turbochargers is 0 gauge or 14.7psi at sea level (ASL).  
 
Throughout the writeup I will refer to sources of boost pressure and vacuum. Vaccum conditions exist only after the throttle body. Boost pressure conditions exist only after the turbochargers. Pressure before the turbochargers is 0 gauge or 14.7psi at sea level (ASL).  
  
I am assuming that readers have reviewed at least the Technical Information Manual on www.stealth316.com, if not the service manual’s explanations of the systems below. I am also assuming that readers have seen and can interpret the [http://www.3si.org/forum/attachment.php?attachmentid=59639 Link to Routing Diagram] from the Service Manual and that they understand the basic function of a turbocharger wastegate.
 
 
What follows is a quick reference only.
 
  
==Systems Removed==
+
'''In this guide, we will be removing the following systems:'''
Exhaust gas recirculation (EGR) solenoid and lines
+
* Exhaust Gas Recirculation (EGR) solenoid and lines
Evaporative emissions (EVAP) solenoid, valve, canister, and lines
+
* Evaporative Emissions (EVAP) solenoid, Valve, Canister, and lines
Boost control solenoid (BCS) and lines
+
* Boost Control Solenoid (BCS) and lines
Fuel pressure regulator solenoid (FPRS) and lines
+
* Fuel Pressure Regulator Solenoid (FPRS) and lines
 +
 
 +
<br style="clear:both;" />
 +
 
 +
== Preparation ==
 +
[[Image:Vacuum_reduction_routing.jpg|thumb|300px|Vacuum Hose Reduction Routing]]
 +
 
 +
=== Background Information ===
 +
I am assuming that readers, at minimum, have:
 +
* Reviewed the Technical Information Manual on www.stealth316.com, if not the service manual’s explanations of the systems below
 +
* Seen and can interpret the vacuum hose reduction routing diagram from the Service Manual displayed to the right
 +
* Established a basic understand of the function of a turbocharger wastegate
  
==Tools Needed==
 
(in order of importance):
 
*Knife
 
*Philips and flathead screwdrivers
 
*3/8 ratchet and socket set (the usual 10mm and 12mm)
 
*Pliers—needlenose, conventional, and the snipping type
 
  
==Materials Needed==
+
=== Tools Needed ===
*4mm vacuum line
+
These are listed in order of importance:
*6mm vacuum line
+
* Knife
*Assorted plastic or brass vacuum tees
+
* Philips Screwdriver
*Vacuum caps
+
* Flathead Screwdrivers
*RTV sealant
+
* 3/8 Ratchet and Socket Set (the usual 10mm and 12mm)
 +
* Pliers (needlenose, conventional, and the snipping type)
  
Remove the following parts in preparation:
 
*Battery
 
*Y-pipe
 
*Front and rear turbo intake pipes
 
*Air filter, MAS, BOV, and intake splitter
 
*Coolant overflow tank (remove the bolts, raise the tank, and rest it on the headlight bucket)
 
  
[NOTE: It is possible to do the hose reduction without removing some of these things, but it is easiest with them removed.]
+
=== Materials Needed ===
 +
* 4mm vacuum line
 +
* 6mm vacuum line
 +
* Assorted plastic or brass vacuum tees
 +
* Vacuum caps
 +
* RTV sealant
  
==Part 1: Deleting the Unnecessary Parts==
 
When you begin, you'll be looking at a nest of vacuum lines and a hardline bundle on the firewall.
 
http://www.pansypatrol.com/people/clint/pictures/vacreduc/Starting%20out.jpg
 
''Brian had already removed a few of his lines, but here you can see the hardline bundle and the solenoid rack''
 
  
http://www.pansypatrol.com/people/clint/pictures/vacreduc/Starting%20out%202.jpg
+
=== Preparing the Engine Bay ===
An alternate view.
+
Before performing the vacuum hose reduction, it'd be a good idea to remove the following parts in preparation (which will be added back after the reduction is completed):
 +
* Battery
 +
* Y-pipe
 +
* Front and rear turbo intake pipes
 +
* Air filter, MAS, BOV, and intake splitter
 +
* Coolant overflow tank (remove the bolts, raise the tank, and rest it on the headlight bucket)
  
Begin the hose reduction by cutting all the vacuum lines running from the hardline bundle on the throttle body (TB) to the solenoid rack on the firewall. Cut the vacuum lines running from the plenum to the H-connector, BCS, and rear wastegate (WG). Cut the vacuum lines running to the EGR valve. Cut the vacuum lines running to the small bundle of hardlines beneath and to the passenger side of the EGR also. (These hard lines connect the BCS and EVAP solenoid to the front wastegate and the EVAP valve respectively. See below for further explanation.)
+
''Note: It is possible to do the hose reduction without removing some of these things, but it is easiest with them removed.''
  
http://www.pansypatrol.com/people/clint/pictures/vacreduc/main%20hoses%20cut.jpg main hoses
 
  
Remove the two upper bolts on the TB. Cut or disconnect the 3 lines running from the hardline bundle to the TB nipples. Remove and discard the hardline bundle. Reinstall the TB bolts.
+
== Step-by-Step Guide ==
  
''(photos to come)''
+
=== Step 1: Delete the Unnecessary Parts ===
 +
When you begin, you'll be looking at a nest of vacuum lines and a hardline bundle near the firewall. Your stock engine bay likely looks similar to the image below. In this photo, a few lines have already been removed, but you can still see the hardline bundle and solenoid rack. The second image is an alternate, close-up view of the same engine bay -- specifically in the area around the solenoid rack.
  
Remove the 3 10mm bolts securing the solenoid rack to the firewall. Disconnect the main electrical connector powering all the solenoids. Remove the solenoid rack.
+
[[Image:Vaccum_hose_reduction-1.jpg|300px|Stock Engine Bay]]
 +
[[Image:Vaccum_hose_reduction-2.jpg|300px|Stock Solenoid Rack]]
  
http://www.pansypatrol.com/people/clint/pictures/vacreduc/solenoid%20rack%20out.jpg
+
==== Cut Vacuum Lines ====
 +
Begin the hose reduction by cutting the following:
 +
* All of the vacuum lines running from the hardline bundle on the Throttle Body (TB) to the Solenoid Rack on the firewall
 +
* The vacuum lines running from the plenum to the H-Connector, Boost Control Solenoid (BCS), and rear Wastegate (WG)
 +
* The vacuum lines running to the EGR valve
 +
* The vacuum lines running to the small bundle of hardlines beneath and to the passenger side of the EGR (''note: these hard lines connect the BCS and EVAP solenoid to the front wastegate and the EVAP valve respectively. See below for further explanation'')
  
At this point there should be no vacuum line remaining in the area of the engine bay between the firewall and the TB/plenum. Move towards the front of the engine bay so that you can remove the EVAP and valve.
+
Here is a photo of the main hoses to cut:
  
Near the front WG actuator and beneath the PTU are hoses coming off of a 4-line hardline bundle. One goes to the front WG actuator; the rest go to the EVAP canister. Cut these.
+
[[Image:Vaccum_hose_reduction-3.jpg|300px|Main hoses to cut]]
  
http://www.pansypatrol.com/people/clint/pictures/vacreduc/Starting%20out%203.jpg
+
==== Remove Hardline Bundle ====
  
Remove the EVAP canister by undoing the band clamp. The EVAP canister is held to the frame rail by a metal band that uses a clasp similar to a mason jar or a ski boot. Because there are some assorted brackets and lines holding the canister itself to the bracket, the best way to remove it is to violently mangle it until it submits. Save the black plastic valve.
+
Next, you will want to:
 +
* Remove the two upper bolts on the Throttle Body (TB)
 +
* Cut (or disconnect) the 3 lines running from the hardline bundle to the Throttle Body nipples
 +
* Remove and discard the hardline bundle
 +
* Reinstall the Throttle Body bolts.
 +
 
 +
The first following photo will show you which Throttle Body bolts to remove and reinstall. The second photo will show you the hardline bundle to be removed.
 +
 
 +
[[Image:Vaccum_hose_reduction-4.jpg|300px|Throttle Body bolts]]
 +
[[Image:Vaccum_hose_reduction-5.jpg|300px|Hardline bundle to remove]]
 +
 
 +
==== Remove Solenoid Rack ====
 +
 
 +
Next, we will be addressing the Solenoid Rack:
 +
* Remove the three 10mm bolts securing the Solenoid Rack to the firewall
 +
* Disconnect the main electrical connector powering all the solenoids
 +
* Remove the Solenoid Rack
 +
 
 +
The first two photos will help you locate where the Solenoid Rack bolts are. The third photo will show you what the Solenoid Rack looks like once removed.
 +
 
 +
[[Image:Vaccum_hose_reduction-6.jpg|300px|Solenoid Rack bolts to remove]]
 +
[[Image:Vaccum_hose_reduction-7.jpg|170px|Solenoid Rack bolts to remove]]
 +
[[Image:Vaccum_hose_reduction-8.jpg|300px|Solenoid Rack removed]]
 +
 
 +
==== Remove EVAP and Valve ====
 +
At this point there should be no vacuum lines remaining in the area of the engine bay between the firewall and the Throttle Body/Plenum. Next we will move towards the front of the engine bay so that you can remove the EVAP and valve.
 +
 
 +
[[Image:Vaccum_hose_reduction-9.jpg|300px|Rear Wastegate and EGR Connections]]
 +
 
 +
Near the front Wastegate Actuator and beneath the PTU are hoses coming off of a 4-line hardline bundle. One goes to the front Wastegate Actuator; the rest go to the EVAP canister. Cut these.
 +
 
 +
[[Image:Vaccum_hose_reduction-10.jpg|300px|Hoses near EVAP]]
 +
 
 +
Next, remove the EVAP canister by undoing the band clamp. The EVAP canister is held to the frame rail by a metal band that uses a clasp similar to a mason jar or a ski boot. Because there are some assorted brackets and lines holding the canister itself to the bracket, the best way to remove it is to violently mangle it until it submits. Save the black plastic valve.
  
 
Further, during removal it is necessary to cut the vacuum hose connecting the canister to the hardline running from the fuel tank to the engine bay (see my quick reference above). The hardline runs along the frame rail (under the MAS), then makes a quick downward turn. It is visible in the upper right hand corner of this photo of the EVAP canister.
 
Further, during removal it is necessary to cut the vacuum hose connecting the canister to the hardline running from the fuel tank to the engine bay (see my quick reference above). The hardline runs along the frame rail (under the MAS), then makes a quick downward turn. It is visible in the upper right hand corner of this photo of the EVAP canister.
  
http://www.pansypatrol.com/people/clint/pictures/vacreduc/evap%20canister.jpg
+
[[Image:Vaccum_hose_reduction-11.jpg|300px|EVAP to Fuel Tank]]
 +
 
 +
==== Remove 4-Line Hardline Bundle ====
 +
The final thing to remove is the 4-line hardline bundle mentioned in the previous steps. These are often a source of confusion for people doing the hose reductions. People are tempted to cap or connect them. All they do is connect the EVAP solenoid and Boost Control lines to the EVAP canister and the front Wastegate. Because the hose reduction removes the solenoids and the stock BC lines, this hardline bundle connects nothing to nothing.
  
The final thing to remove is the 4-line hardline bundle mentioned just earlier. These are often a source of confusion for people doing the hose reductions. People are tempted to cap or connect them. All they do is connect the EVAP solenoid and BC lines to the EVAP canister and the front WG. Because the hose reduction removes the solenoids and the stock BC lines, this hardline bundle connects nothing to nothing.
+
The bundle runs the alongside the engine. They begin beneath the EGR valve, turning down under the throttle body. They run under the thermostat housing and under the coil packs. They terminate about 3 inches away from the front Wastegate Actuator diaphragm.  
The bundle runs the alongside the engine, beginning beneath the EGR valve, turning down under the throttle body, under the thermostat housing, under the coil packs, and terminating about 3 inches away from the front WG actuator diaphragm.  
 
  
http://www.pansypatrol.com/people/clint/pictures/vacreduc/hardlines.jpg
+
[[Image:Vaccum_hose_reduction-12.jpg|300px|4-Line Hardline Bundle]]
  
 
It will require some yanking and bending to remove. Do not expect it to slide out instantly.
 
It will require some yanking and bending to remove. Do not expect it to slide out instantly.
  
==Part 2: Providing Sources of Vacuum and Pressure to Systems that Require Them==
+
 
 +
=== Step 2: Provide Sources of Vacuum/Pressure to Required Systems ===
 
Now that everything is out, prepare to install your own vacuum lines.
 
Now that everything is out, prepare to install your own vacuum lines.
  
The FPR must see vacuum and pressure to function properly because it increases or decreases fuel rail pressure according to manifold pressure. The most direct way to connect the FPR is to use the large forward-facing port on the plenum. Notice that the nipple sizes are not the same.  
+
The Fuel Pressure Regulator (FPR) must see vacuum and pressure to function properly because it increases or decreases fuel rail pressure according to manifold pressure. The most direct way to connect the FPR is to use the large forward-facing port on the plenum. Notice that the nipple sizes are not the same.  
  
 
http://www.pansypatrol.com/people/clint/pictures/vacreduc/FPRline.jpg
 
http://www.pansypatrol.com/people/clint/pictures/vacreduc/FPRline.jpg
  
As you can see above, the cleanest method of connecting the FPR to a pressure/vacuum source is to use a plastic T: Plenum port-T-FPR. Not only can you get a plastic T with differently-sized ports to solve the nipple size problem, but you can also then run a vacuum line from that T to the BOV, which also requires a vacuum/pressure source to operate properly.
+
[[Image:Vaccum_hose_reduction-13.jpg|300px|Fuel Pressure Regulator (FPR) Line]]
  
Connecting the wastegates: The WGs do not need a vacuum signal; they need only a pressure signal. My preferred method is to run a lines from the wastegates to a T located roughly where the thermostat housing is. Make these lines equal length and as short as possible. Be reasonable: do not make them so tight that you can pluck them like guitar strings. Run a line from the remaining port on the T to the MBC or BCS (depending on setup). This portion of the house routing is unique. Place the MBC or BCS wherever you prefer. Mine is on the firewall. Finally, connect your MBC or BCS to nipple on the back of the Y-pipe. Usually I just attach an excessively long line to the MBC or BCS “in” port until the very end, and then cut the line to length once I’ve installed the Y-pipe.
+
As you can see above, the cleanest method of connecting the FPR to a pressure/vacuum source is to use a plastic T: Plenum port-T-FPR. Not only can you get a plastic T with differently sized ports to solve the nipple size problem, but you can also then run a vacuum line from that T to the Blow-off Valve (BOV), which also requires a vacuum/pressure source to operate properly.  
http://www.pansypatrol.com/people/clint/pictures/vacreduc/WGtee.jpg
 
In this photo, I am holding the rear WG line. The tee is at center. Top line goes to BC and right line goes to front WG.
 
  
Because the EVAP canister is out, gasoline fumes will now vent into the engine bay, which is less than desirable. There are 2 easy options: Cap the hardline with a vacuum cap, or run a length hose from the hardline out the front of the bumper. I prefer this second method because pressure does not build in the tank. Ultimately, the best way is to remove the rock guard, cut the hardline back at the tank, and remove the hardline entirely.
+
==== Connect the Wastegates ====
 +
The Wastegates do not need a vacuum signal; they need only a pressure signal.
  
http://www.pansypatrol.com/people/clint/pictures/vacreduc/ventline2.jpg
+
My preferred method is to run lines from the Wastegates to a T located roughly near where the thermostat housing is. Make these lines equal length and as short as possible. Be reasonable: do not make them so tight that you can pluck them like guitar strings. Run a line from the remaining port on the T to the Manual Boost Controller (MBC) or Boost Control Solenoid (BCS), depending on your setup. This portion of the house routing is unique. Place the MBC or BCS wherever you prefer. Mine is on the firewall.
  
http://www.pansypatrol.com/people/clint/pictures/vacreduc/ventline.jpg
+
Finally, connect your MBC or BCS to nipple on the back of the Y-pipe. Usually I just attach an excessively long line to the MBC or BCS "in" port until the very end, and then cut the line to length once I’ve installed the Y-pipe.
  
If you have a boost gauge, connect it to a vacuum/pressure source like the nipple on the back of the plenum. If you have other switches or units (hobbs switches, MAP sensors), connect them.
+
=== Add a Gas Fumes Vent Line ===
 +
Because the EVAP canister is out, gasoline fumes will now vent into the engine bay, which is less than desirable. There are 2 easy options:
 +
# Cap the hardline with a vacuum cap, or
 +
# Run a length hose from the hardline out the front of the bumper
  
==Part 3: Capping Unused Ports==
+
I prefer this second method because pressure does not build in the tank. Ultimately, the best way is to remove the rock guard, cut the hardline back at the tank, and remove the hardline entirely.
To prevent intake tract leaks it is important to cap all unused nipples. There are two on the pre-turbo intake pipes: A small one on the rear turbo pipe (recall that it was used to reintroduce bled air on the stock BC system) and a large one on the front turbo intake pipe.
 
  
For the rear, use a vacuum cap (I like to slather a little RTV on there too).
+
=== Connect Boost Gauge ===
 +
If you have a boost gauge, connect it to a vacuum/pressure source -- such as the nipple on the back of the plenum. If you have other switches or units (hobbs switches, MAP sensors), it is now a good idea to connect them.  
  
http://www.pansypatrol.com/people/clint/pictures/vacreduc/rearturbocap.jpg
 
  
For the front, you may simply use the EVAP canister valve because it defaults to the closed position.  
+
=== Step 3: Cap Unused Ports ===
 +
To prevent intake tract leaks it is important to cap all unused nipples. There are two on the pre-turbo intake pipes:
 +
* A small one on the rear turbo pipe (recall that it was used to reintroduce bled air on the stock Boost Control system)
 +
* A large one on the front turbo intake pipe.
  
Advanced techniques: Fill the port with RTV or, if you wish to be challenged, find a vacuum cap in that size that seals well. I prefer the RTV.
+
For the rear, use a vacuum cap (I like to slather a little RTV on there too). For the front, you may simply use the EVAP canister valve because it defaults to the closed position.  
  
http://www.pansypatrol.com/people/clint/pictures/vacreduc/RTVnipple.jpg
+
If you'd like to get a little more advanced, I suggest you fill the port with RTV or, if you wish to be challenged, find a vacuum cap in that size that seals well. I prefer the RTV.
  
Cap the nipples on the throttle body.
+
Additionally, cap the nipples on the throttle body.
  
(photo)
+
If you have EGR blockoff plates, install them now.
  
If you have EGR blockoff plates, install them now.
 
  
==Part 4: Reinstallation==
+
=== Step 4: Reinstall ===
Reinstall the intake piping and the coolant reservoir. It will likely be much easier now. Ensure that you do not pinch the WG signal lines.
+
Reinstall the intake piping and the coolant reservoir. It will likely be much easier now. Ensure that you do not pinch the Wastegate signal lines.
  
 
At this time, you will also want to connect the BOV. If you removed the BOV with its stock vacuum line attached, and it will reach, connect it to the T between the large plenum nipple and the FPR. If the line will not reach, simply make a new one.
 
At this time, you will also want to connect the BOV. If you removed the BOV with its stock vacuum line attached, and it will reach, connect it to the T between the large plenum nipple and the FPR. If the line will not reach, simply make a new one.
Line 126: Line 176:
 
Similarly, you should remember to cut to length and then attach the MBC or BCS to the Y-pipe nipple.
 
Similarly, you should remember to cut to length and then attach the MBC or BCS to the Y-pipe nipple.
  
==Supplemental Info==
+
 
 +
== Supplemental Information ==
 
I like to approach the hose reduction with a hack-and-slash disregard for the engine bay. Remember that it’s all just hoses and systems that are unnecessary anyway. There’s nothing to “break” or damage unless you cut wires or a coolant hose (and for that you have only yourself to blame).
 
I like to approach the hose reduction with a hack-and-slash disregard for the engine bay. Remember that it’s all just hoses and systems that are unnecessary anyway. There’s nothing to “break” or damage unless you cut wires or a coolant hose (and for that you have only yourself to blame).
  
 
Similarly, as I’ve said many times in various threads, a hose reduction is a hose reduction. There is no such thing as a “hose reduction for X boost controller”. All boost controllers accept a pressure signal and then modify and transmit that signal to the wastegates.
 
Similarly, as I’ve said many times in various threads, a hose reduction is a hose reduction. There is no such thing as a “hose reduction for X boost controller”. All boost controllers accept a pressure signal and then modify and transmit that signal to the wastegates.
  
It seems a little senseless to me to do a hose reduction and not install EGR blockoff plates and at least an MBC and inexpensive boost gauge at the same time. If you’re committed to the hose reduction and to an emptier engine bay, blockoff plates are a small price to pay. A boost gauge is a must for any turbo car, in my opinion, and if you’re comfortable enough with your engine to be performing a hose reduction, you probably intend to run more boost at some point or at least have an interest in how your engine is running. And, lastly, an MBC is 20 dollars. Doing the hose reduction without installing at least an MBC and gauge requires that you retain the stock BC lines and the solenoid rack, or that you connect the WG directly to a pressure source and run WG pressure (6psi).  
+
=== EGR Blockoff Plates, MBC, and Boost Gauge ===
 +
It seems a little senseless to me to do a hose reduction and not install EGR blockoff plates, a Manual Boost Controller (at least), and an inexpensive boost gauge at the same time. If you’re committed to the hose reduction and to an emptier engine bay, blockoff plates are a small price to pay. A boost gauge is a must for any turbo car, in my opinion, and if you’re comfortable enough with your engine to be performing a hose reduction, you probably intend to run more boost at some point or at least have an interest in how your engine is running. And, lastly, an MBC is 20 dollars. Doing the hose reduction without installing at least an MBC and gauge requires that you retain the stock BC lines and the solenoid rack, or that you connect the WG directly to a pressure source and run WG pressure (6psi).
 +
 
  
Clint
+
== Credits ==
 +
* Main Guide Provided By: Struggly (Clint)
 +
* Photos Provided By: timothyj94

Revision as of 21:47, September 28, 2015


How to Perform a Vacuum Hose Reduction on a Mitsubishi 3000GT / Dodge Stealth[edit]

This guides explains the vacuum hose reduction for the first generation 1991-1993 Mitsubishi 3000GT and Dodge Stealth; specifically the Federal Spec ’91-93, California Spec ’91-93, and 2G Hybrid ECU ’94-95 cars. Below are brief descriptions of the systems involved, a list of tools required to perform the modification, and step-by-step instructions for the modification itself. It is intended to be a general guide only; hose reductions will vary according to individual setups and preferences.

Throughout the writeup I will refer to sources of boost pressure and vacuum. Vaccum conditions exist only after the throttle body. Boost pressure conditions exist only after the turbochargers. Pressure before the turbochargers is 0 gauge or 14.7psi at sea level (ASL).


In this guide, we will be removing the following systems:

  • Exhaust Gas Recirculation (EGR) solenoid and lines
  • Evaporative Emissions (EVAP) solenoid, Valve, Canister, and lines
  • Boost Control Solenoid (BCS) and lines
  • Fuel Pressure Regulator Solenoid (FPRS) and lines


Preparation[edit]

Vacuum Hose Reduction Routing

Background Information[edit]

I am assuming that readers, at minimum, have:

  • Reviewed the Technical Information Manual on www.stealth316.com, if not the service manual’s explanations of the systems below
  • Seen and can interpret the vacuum hose reduction routing diagram from the Service Manual displayed to the right
  • Established a basic understand of the function of a turbocharger wastegate


Tools Needed[edit]

These are listed in order of importance:

  • Knife
  • Philips Screwdriver
  • Flathead Screwdrivers
  • 3/8 Ratchet and Socket Set (the usual 10mm and 12mm)
  • Pliers (needlenose, conventional, and the snipping type)


Materials Needed[edit]

  • 4mm vacuum line
  • 6mm vacuum line
  • Assorted plastic or brass vacuum tees
  • Vacuum caps
  • RTV sealant


Preparing the Engine Bay[edit]

Before performing the vacuum hose reduction, it'd be a good idea to remove the following parts in preparation (which will be added back after the reduction is completed):

  • Battery
  • Y-pipe
  • Front and rear turbo intake pipes
  • Air filter, MAS, BOV, and intake splitter
  • Coolant overflow tank (remove the bolts, raise the tank, and rest it on the headlight bucket)

Note: It is possible to do the hose reduction without removing some of these things, but it is easiest with them removed.


Step-by-Step Guide[edit]

Step 1: Delete the Unnecessary Parts[edit]

When you begin, you'll be looking at a nest of vacuum lines and a hardline bundle near the firewall. Your stock engine bay likely looks similar to the image below. In this photo, a few lines have already been removed, but you can still see the hardline bundle and solenoid rack. The second image is an alternate, close-up view of the same engine bay -- specifically in the area around the solenoid rack.

Stock Engine Bay Stock Solenoid Rack

Cut Vacuum Lines[edit]

Begin the hose reduction by cutting the following:

  • All of the vacuum lines running from the hardline bundle on the Throttle Body (TB) to the Solenoid Rack on the firewall
  • The vacuum lines running from the plenum to the H-Connector, Boost Control Solenoid (BCS), and rear Wastegate (WG)
  • The vacuum lines running to the EGR valve
  • The vacuum lines running to the small bundle of hardlines beneath and to the passenger side of the EGR (note: these hard lines connect the BCS and EVAP solenoid to the front wastegate and the EVAP valve respectively. See below for further explanation)

Here is a photo of the main hoses to cut:

Main hoses to cut

Remove Hardline Bundle[edit]

Next, you will want to:

  • Remove the two upper bolts on the Throttle Body (TB)
  • Cut (or disconnect) the 3 lines running from the hardline bundle to the Throttle Body nipples
  • Remove and discard the hardline bundle
  • Reinstall the Throttle Body bolts.

The first following photo will show you which Throttle Body bolts to remove and reinstall. The second photo will show you the hardline bundle to be removed.

Throttle Body bolts Hardline bundle to remove

Remove Solenoid Rack[edit]

Next, we will be addressing the Solenoid Rack:

  • Remove the three 10mm bolts securing the Solenoid Rack to the firewall
  • Disconnect the main electrical connector powering all the solenoids
  • Remove the Solenoid Rack

The first two photos will help you locate where the Solenoid Rack bolts are. The third photo will show you what the Solenoid Rack looks like once removed.

Solenoid Rack bolts to remove Solenoid Rack bolts to remove Solenoid Rack removed

Remove EVAP and Valve[edit]

At this point there should be no vacuum lines remaining in the area of the engine bay between the firewall and the Throttle Body/Plenum. Next we will move towards the front of the engine bay so that you can remove the EVAP and valve.

Rear Wastegate and EGR Connections

Near the front Wastegate Actuator and beneath the PTU are hoses coming off of a 4-line hardline bundle. One goes to the front Wastegate Actuator; the rest go to the EVAP canister. Cut these.

Hoses near EVAP

Next, remove the EVAP canister by undoing the band clamp. The EVAP canister is held to the frame rail by a metal band that uses a clasp similar to a mason jar or a ski boot. Because there are some assorted brackets and lines holding the canister itself to the bracket, the best way to remove it is to violently mangle it until it submits. Save the black plastic valve.

Further, during removal it is necessary to cut the vacuum hose connecting the canister to the hardline running from the fuel tank to the engine bay (see my quick reference above). The hardline runs along the frame rail (under the MAS), then makes a quick downward turn. It is visible in the upper right hand corner of this photo of the EVAP canister.

EVAP to Fuel Tank

Remove 4-Line Hardline Bundle[edit]

The final thing to remove is the 4-line hardline bundle mentioned in the previous steps. These are often a source of confusion for people doing the hose reductions. People are tempted to cap or connect them. All they do is connect the EVAP solenoid and Boost Control lines to the EVAP canister and the front Wastegate. Because the hose reduction removes the solenoids and the stock BC lines, this hardline bundle connects nothing to nothing.

The bundle runs the alongside the engine. They begin beneath the EGR valve, turning down under the throttle body. They run under the thermostat housing and under the coil packs. They terminate about 3 inches away from the front Wastegate Actuator diaphragm.

4-Line Hardline Bundle

It will require some yanking and bending to remove. Do not expect it to slide out instantly.


Step 2: Provide Sources of Vacuum/Pressure to Required Systems[edit]

Now that everything is out, prepare to install your own vacuum lines.

The Fuel Pressure Regulator (FPR) must see vacuum and pressure to function properly because it increases or decreases fuel rail pressure according to manifold pressure. The most direct way to connect the FPR is to use the large forward-facing port on the plenum. Notice that the nipple sizes are not the same.

FPRline.jpg

Fuel Pressure Regulator (FPR) Line

As you can see above, the cleanest method of connecting the FPR to a pressure/vacuum source is to use a plastic T: Plenum port-T-FPR. Not only can you get a plastic T with differently sized ports to solve the nipple size problem, but you can also then run a vacuum line from that T to the Blow-off Valve (BOV), which also requires a vacuum/pressure source to operate properly.

Connect the Wastegates[edit]

The Wastegates do not need a vacuum signal; they need only a pressure signal.

My preferred method is to run lines from the Wastegates to a T located roughly near where the thermostat housing is. Make these lines equal length and as short as possible. Be reasonable: do not make them so tight that you can pluck them like guitar strings. Run a line from the remaining port on the T to the Manual Boost Controller (MBC) or Boost Control Solenoid (BCS), depending on your setup. This portion of the house routing is unique. Place the MBC or BCS wherever you prefer. Mine is on the firewall.

Finally, connect your MBC or BCS to nipple on the back of the Y-pipe. Usually I just attach an excessively long line to the MBC or BCS "in" port until the very end, and then cut the line to length once I’ve installed the Y-pipe.

Add a Gas Fumes Vent Line[edit]

Because the EVAP canister is out, gasoline fumes will now vent into the engine bay, which is less than desirable. There are 2 easy options:

  1. Cap the hardline with a vacuum cap, or
  2. Run a length hose from the hardline out the front of the bumper

I prefer this second method because pressure does not build in the tank. Ultimately, the best way is to remove the rock guard, cut the hardline back at the tank, and remove the hardline entirely.

Connect Boost Gauge[edit]

If you have a boost gauge, connect it to a vacuum/pressure source -- such as the nipple on the back of the plenum. If you have other switches or units (hobbs switches, MAP sensors), it is now a good idea to connect them.


Step 3: Cap Unused Ports[edit]

To prevent intake tract leaks it is important to cap all unused nipples. There are two on the pre-turbo intake pipes:

  • A small one on the rear turbo pipe (recall that it was used to reintroduce bled air on the stock Boost Control system)
  • A large one on the front turbo intake pipe.

For the rear, use a vacuum cap (I like to slather a little RTV on there too). For the front, you may simply use the EVAP canister valve because it defaults to the closed position.

If you'd like to get a little more advanced, I suggest you fill the port with RTV or, if you wish to be challenged, find a vacuum cap in that size that seals well. I prefer the RTV.

Additionally, cap the nipples on the throttle body.

If you have EGR blockoff plates, install them now.


Step 4: Reinstall[edit]

Reinstall the intake piping and the coolant reservoir. It will likely be much easier now. Ensure that you do not pinch the Wastegate signal lines.

At this time, you will also want to connect the BOV. If you removed the BOV with its stock vacuum line attached, and it will reach, connect it to the T between the large plenum nipple and the FPR. If the line will not reach, simply make a new one.

Similarly, you should remember to cut to length and then attach the MBC or BCS to the Y-pipe nipple.


Supplemental Information[edit]

I like to approach the hose reduction with a hack-and-slash disregard for the engine bay. Remember that it’s all just hoses and systems that are unnecessary anyway. There’s nothing to “break” or damage unless you cut wires or a coolant hose (and for that you have only yourself to blame).

Similarly, as I’ve said many times in various threads, a hose reduction is a hose reduction. There is no such thing as a “hose reduction for X boost controller”. All boost controllers accept a pressure signal and then modify and transmit that signal to the wastegates.

EGR Blockoff Plates, MBC, and Boost Gauge[edit]

It seems a little senseless to me to do a hose reduction and not install EGR blockoff plates, a Manual Boost Controller (at least), and an inexpensive boost gauge at the same time. If you’re committed to the hose reduction and to an emptier engine bay, blockoff plates are a small price to pay. A boost gauge is a must for any turbo car, in my opinion, and if you’re comfortable enough with your engine to be performing a hose reduction, you probably intend to run more boost at some point or at least have an interest in how your engine is running. And, lastly, an MBC is 20 dollars. Doing the hose reduction without installing at least an MBC and gauge requires that you retain the stock BC lines and the solenoid rack, or that you connect the WG directly to a pressure source and run WG pressure (6psi).


Credits[edit]

  • Main Guide Provided By: Struggly (Clint)
  • Photos Provided By: timothyj94