Drivetrain: Replace Carrier Bearing - Revision history

Stealthify: Typo fix

2012-09-04T13:04:54Z

Typo fix

Stealthify: Improved text readability by emboldening the key instructions.

2012-09-04T12:41:04Z

Improved text readability by emboldening the key instructions.

Stealthify at 03:30, September 4, 2012

2012-09-04T03:30:30Z

Stealthify: Added categories

2012-09-03T15:49:21Z

Added categories

Stealthify at 15:44, September 3, 2012

2012-09-03T15:44:29Z

Stealthify: Mirrored Toni's carrier bearing tutorial (http://www.primaryboost.com/)

2012-09-03T15:43:04Z

Mirrored Toni's carrier bearing tutorial (http://www.primaryboost.com/)

New page

Replacing the carrier bearings is a lengthy repair. If your car has some age on it chances are they are worn and can create knocking problems or excess vibration.

==Tools Needed==
*Various Hand Tools
*Screwdrivers
*Impact Wrench ''(not necessary but it makes the job many times easier)''
*Jacks
*Jack Stands '''(A MUST! when you are working under the car)'''
*Gear Puller ''(three jaw is best)''

==Parts Needed==
{| class="wikitable"
! Qty
! Part Number
! Part Name
! Notes
|-
|style="text-align:center;"| 2x
| MB505495
| Carrier Bearings
|
|-
|style="text-align:center;"| 4x
| MB505283
| Carrier Bearing Insulator
|rowspan="2" valign="top"|''If yours are worn''
|-
|style="text-align:center;"| 4x
| MB505284
| Carrier Bearing Insulator
|-
|style="text-align:center;"| 1x
| MB837572
| Lobro Joint Boot Kit
| ''If you need to replace your boot''
|-
|style="text-align:center;"| .35qt
| ''n/a''
| Transfer Case GL-4 Rated Gear Oil
| ''Redline Shockproof Heavy recommend''
|}

==Preparation==
#Jack up the car and place on jack stands
#Remove the fill plug from the transfer case
#Remove the drain plug and drain the fluid

=Replacing the Carrier Bearing in a Mitsubishi 3000GT/GTO VR4 or Dodge Stealth RT/TT=
==Unbold the Driveshaft==
#Mark where the driveshaft meets up to the rear differential so the orientation is maintained upon installation and remove the four bolts. Leave one in to hold it as you remove the rest of the shaft.
#:[[File:carrier_bearing-rearshaft_diff.jpg|thumb|none|250px|Driveshaft meets rear differential]]
#Support the driveshaft with a few jacks or some blocks, you don't want it to drop or bend at the lobro joint too much.
#Unbolt the two nuts at the '''rear carrier bearing'''. They are lock nuts so they will be tight the whole length of the stud. There may be some spacers so be sure to keep track of which stud they are on.
#:[[File:carrier_bearing-rear.jpg|thumb|none|250px|Rear carrier bearing]]
#Unbolt the exhaust hanger then the remaining two nuts holding the '''front carrier bearing''' on.
#:[[File:carrier_bearing-front.jpg|thumb|none|250px|Front carrier bearing]]
#Once you have everything unbolted you can drop the shaft and pull it out of the transfercase. Leave an oil pan underneath the transfercase as some gear oil will come out. Again be sure to keep the shaft straight, a second hand will help here. Also be sure not to scratch the end that goes into the transfercase and is a good idea to wrap and tape it.
#:[[File:carrier_bearing-frontshaft_transfercase.jpg|thumb|none|250px|Driveshaft meets transfer case]]

==Remove the Front and Rear Carrier Bearings==
#Here you see the shaft out of the car. The lobro joint is that between the two bearings.
#:[[File:carrier_bearing-shaft_removed.jpg|thumb|none|250px|Driveshaft (removed from car)]]
#Make a mating mark between the front shaft and the rear two so they may be lined up upon assembly. Unbolt the four bolts.
#:[[File:carrier_bearing-front_rear_connected.jpg|thumb|left|250px|Front and Rear connected]][[File:carrier_bearing-front_rear_disconnected.jpg|thumb|none|250px|Front and Rear disconnected]] 
#Make a mark on the center shaft and the companion flange.
#:[[File:carrier_bearing-front_companion_marked.jpg|thumb|none|250px|Front companion joint marked]]
#Unbolt the nut inside the on front companion joint. It is on there with 137ft lbs, impact wrench works nicely here, otherwise you will have to put the shaft in a vise. Be sure to remove the washer underneath.
#:[[File:carrier_bearing-front_companion_nut.jpg|thumb|none|250px|Unbolted nut from the front companion joint]]
#Use a puller to pull off the companion flange.
#:[[File:carrier_bearing-front_companion_puller.jpg|thumb|left|250px|Remove the companion flange with the puller]] [[File:carrier_bearing-front_companion_removed.jpg|thumb|none|250px|The front companion flange removed]] 
#Pry off the outside of the carrier bearing. It might take some force (pictured is the rear bearing but the process is the same)
#:[[File:carrier_bearing-outer_rubber.jpg|thumb|left|250px|Pry off the outer rubber from the carrier bearing]] [[File:carrier_bearing-front_rubber_bracket_removed.jpg|thumb|none|250px|The outside rubber/bracket removed]] 
#Use a gear puller to remove the rest of the bearing.
#:[[File:carrier_bearing-front_puller.jpg|thumb|left|250px|Pull the front carrier bearing]] [[File:carrier_bearing-front_removed.jpg|thumb|none|250px|Front carrier bearing removed]] 
#Mark the rear shaft, center shaft, companion flange, and lobro joint to ensure alignment.
#:[[File:carrier_bearing-lobro_marked.jpg|thumb|none|250px|Mark the rear/center shaft, companion and lobro joint]]
#Unbolt the lobro joint from the companion flange. There will be a lot of grease inside, I would recommend wearing gloves at this point.
#:[[File:carrier_bearing-lobro_companion_unbolted.jpg|thumb|none|250px|Unbolt the lobro joint]]
#Unbolt the nut from the rear companion flange. Be sure to remove the washer from inside as well.
#:[[File:carrier_bearing-rear_companion_nut.jpg|thumb|left|250px|Unbolt the nut from the rear companion flange]] [[File:carrier_bearing-rear_companion_nut_removed.jpg|thumb|none|250px|Unbolted nut from the rear companion flange]] 
#Pull the rear companion flange off.
#:[[File:carrier_bearing-rear_companion_puller.jpg|thumb|none|250px|Pull off the rear companion flange]]
#Pry off the outside of the carrier bearing. It might take some force.
#:[[File:carrier_bearing-outer_rubber.jpg|thumb|none|250px|Pry off the outer rubber from the carrier bearing]]
#Pull the rest of the bearing off.
#:[[File:carrier_bearing-rear_removed.jpg|thumb|none|250px|Remove the rear carrier bearing]]

==Install the New Carrier Bearings==
At this point you may start installation of the bearings. If you need to replace your lobro boot continue on below.

There are two sides to the carrier bearing, one has a dust sheild (shown below) and should always face the companion flange.

[[File:carrier_bearing-dust_shield.jpg|thumb|none|250px|The dust shield side of a carrier bearing]]

Install the bearing, and the companion flange making sure to align all marks previously made. Use the companion flange to tighten and press the bearing back on. Torque to 137 ft lbs.

[[File:carrier_bearing-install.jpg|thumb|none|250px|Install the new carrier bearings]]

==Reassemble Driveshaft==
At this point you can reinstall making sure to align all marks made. Don't forget to fill the transfercase.
[[File:driveshaft_diagram.jpg|thumb|none|550px|Driveshaft Assembly Diagram]]
{{Origin website
| author_name=Toni
| website_address=http://www.primaryboost.com/homepage/cars/faqs/driveshaft/driveshaft.html
| website_title=Antoni's 3000GT/Stealth Website
}}

@@ Line 56: / Line 56: @@
 #'''Unbolt the two nuts at the rear carrier bearing'''. They are lock nuts so they will be tight the whole length of the stud. There may be some spacers so be sure to keep track of which stud they are on.
 #:[[File:carrier_bearing-rear.jpg|thumb|none|250px|Rear carrier bearing]]
-#'''Unbolt the exhaust hanger then the remaining two nuts holding on the front carrier bearing'''.
+#'''Unbolt the exhaust hanger and then the remaining two nuts holding on the front carrier bearing'''.
 #:[[File:carrier_bearing-front.jpg|thumb|none|250px|Front carrier bearing]]
 #'''Drop the shaft'''. Once you have everything unbolted you can drop the shaft and pull it out of the transfercase. Leave an oil pan underneath the transfercase as some gear oil will come out. Again be sure to keep the shaft straight, a second hand will help here. Also be sure not to scratch the end that goes into the transfercase and is a good idea to wrap and tape it.

← Older revision		Revision as of 15:49, September 3, 2012
Line 1:		Line 1:
		+	[[Category:How To]]
		+	[[Category:Drivetrain]]
	Replacing the carrier bearings is a lengthy repair. If your car has some age on it chances are they are worn and can create knocking problems or excess vibration.		Replacing the carrier bearings is a lengthy repair. If your car has some age on it chances are they are worn and can create knocking problems or excess vibration.

@@ Line 51: / Line 51: @@
 =Replacing the Carrier Bearings in a Mitsubishi 3000GT/GTO VR4 or Dodge Stealth RT/TT=
 ==Unbold the Driveshaft==
-#Mark where the driveshaft meets up to the rear differential so the orientation is maintained upon installation and remove the four bolts. Leave one in to hold it as you remove the rest of the shaft.
+#'''Mark where the driveshaft meets up to the rear differential'''. This is so that the orientation is maintained upon installation and remove the four bolts. Leave one in to hold it as you remove the rest of the shaft.
 #:[[File:carrier_bearing-rearshaft_diff.jpg|thumb|none|250px|Driveshaft meets rear differential]]
-#Support the driveshaft with a few jacks or some blocks, you don't want it to drop or bend at the lobro joint too much.
+#'''Support the driveshaft with a few jacks or some blocks'''. You don't want it to drop or bend at the lobro joint too much.
-#Unbolt the two nuts at the '''rear carrier bearing'''. They are lock nuts so they will be tight the whole length of the stud. There may be some spacers so be sure to keep track of which stud they are on.
+#'''Unbolt the two nuts at the rear carrier bearing'''. They are lock nuts so they will be tight the whole length of the stud. There may be some spacers so be sure to keep track of which stud they are on.
 #:[[File:carrier_bearing-rear.jpg|thumb|none|250px|Rear carrier bearing]]
-#Unbolt the exhaust hanger then the remaining two nuts holding the '''front carrier bearing''' on.
+#'''Unbolt the exhaust hanger then the remaining two nuts holding on the front carrier bearing'''.
 #:[[File:carrier_bearing-front.jpg|thumb|none|250px|Front carrier bearing]]
-#Once you have everything unbolted you can drop the shaft and pull it out of the transfercase. Leave an oil pan underneath the transfercase as some gear oil will come out. Again be sure to keep the shaft straight, a second hand will help here. Also be sure not to scratch the end that goes into the transfercase and is a good idea to wrap and tape it.
+#'''Drop the shaft'''. Once you have everything unbolted you can drop the shaft and pull it out of the transfercase. Leave an oil pan underneath the transfercase as some gear oil will come out. Again be sure to keep the shaft straight, a second hand will help here. Also be sure not to scratch the end that goes into the transfercase and is a good idea to wrap and tape it.
 #:[[File:carrier_bearing-frontshaft_transfercase.jpg|thumb|none|250px|Driveshaft meets transfer case]]
 ==Remove the Front and Rear Carrier Bearings==
-#Here you see the shaft out of the car. The lobro joint is that between the two bearings.
+Here you see the shaft out of the car. The lobro joint is that between the two bearings.
-#:[[File:carrier_bearing-shaft_removed.jpg|thumb|none|250px|Driveshaft (removed from car)]]
-#Make a mating mark between the front shaft and the rear two so they may be lined up upon assembly. Unbolt the four bolts.
+[[File:carrier_bearing-shaft_removed.jpg|thumb|none|250px|Driveshaft (removed from car)]]
 #:[[File:carrier_bearing-front_rear_connected.jpg|thumb|left|250px|Front and Rear connected]][[File:carrier_bearing-front_rear_disconnected.jpg|thumb|none|250px|Front and Rear disconnected]]<br style="clear:both;" />
-#Make a mark on the center shaft and the companion flange.
+#'''Make a mark on the center shaft and the companion flange'''.
 #:[[File:carrier_bearing-front_companion_marked.jpg|thumb|none|250px|Front companion joint marked]]
-#Unbolt the nut inside the on front companion joint. It is on there with 137ft lbs, impact wrench works nicely here, otherwise you will have to put the shaft in a vise. Be sure to remove the washer underneath.
+#'''Unbolt the nut inside the on front companion joint'''. It is on there with 137ft lbs, impact wrench works nicely here, otherwise you will have to put the shaft in a vise. Be sure to remove the washer underneath.
 #:[[File:carrier_bearing-front_companion_nut.jpg|thumb|none|250px|Unbolted nut from the front companion joint]]
-#Use a puller to pull off the companion flange.
+#'''Use a puller to pull off the companion flange'''.
 #:[[File:carrier_bearing-front_companion_puller.jpg|thumb|left|250px|Remove the companion flange with the puller]] [[File:carrier_bearing-front_companion_removed.jpg|thumb|none|250px|The front companion flange removed]]<br style="clear:both;" />
-#Pry off the outside of the carrier bearing. It might take some force (pictured is the rear bearing but the process is the same)
+#'''Pry off the outside of the carrier bearing'''. It might take some force (pictured is the rear bearing but the process is the same)
 #:[[File:carrier_bearing-outer_rubber.jpg|thumb|left|250px|Pry off the outer rubber from the carrier bearing]] [[File:carrier_bearing-front_rubber_bracket_removed.jpg|thumb|none|250px|The outside rubber/bracket removed]]<br style="clear:both" />
-#Use a gear puller to remove the rest of the bearing.
+#'''Use a gear puller to remove the rest of the bearing'''.
 #:[[File:carrier_bearing-front_puller.jpg|thumb|left|250px|Pull the front carrier bearing]] [[File:carrier_bearing-front_removed.jpg|thumb|none|250px|Front carrier bearing removed]]<br style="clear:both;" />
-#Mark the rear shaft, center shaft, companion flange, and lobro joint to ensure alignment.
+#'''Mark the rear shaft, center shaft, companion flange, and lobro joint'''. This is to ensure alignment.
 #:[[File:carrier_bearing-lobro_marked.jpg|thumb|none|250px|Mark the rear/center shaft, companion and lobro joint]]
-#Unbolt the lobro joint from the companion flange. There will be a lot of grease inside, I would recommend wearing gloves at this point.
+#'''Unbolt the lobro joint from the companion flange'''. There will be a lot of grease inside, I would recommend wearing gloves at this point.
 #:[[File:carrier_bearing-lobro_companion_unbolted.jpg|thumb|none|250px|Unbolt the lobro joint]]
-#Unbolt the nut from the rear companion flange. Be sure to remove the washer from inside as well.
+#'''Unbolt the nut from the rear companion flange'''. Be sure to remove the washer from inside as well.
 #:[[File:carrier_bearing-rear_companion_nut.jpg|thumb|left|250px|Unbolt the nut from the rear companion flange]] [[File:carrier_bearing-rear_companion_nut_removed.jpg|thumb|none|250px|Unbolted nut from the rear companion flange]]<br style="clear:both" />
-#Pull the rear companion flange off.
+#'''Pull the rear companion flange off'''.
 #:[[File:carrier_bearing-rear_companion_puller.jpg|thumb|none|250px|Pull off the rear companion flange]]
-#Pry off the outside of the carrier bearing. It might take some force.
+#'''Pry off the outside of the carrier bearing'''. It might take some force.
 #:[[File:carrier_bearing-outer_rubber.jpg|thumb|none|250px|Pry off the outer rubber from the carrier bearing]]
-#Pull the rest of the bearing off.
+#'''Pull the rest of the bearing off'''.
 #:[[File:carrier_bearing-rear_removed.jpg|thumb|none|250px|Remove the rear carrier bearing]]

@@ Line 40: / Line 40: @@
 | ''n/a''
 | Transfer Case GL-4 Rated Gear Oil
-| ''Redline Shockproof Heavy recommend''
+| ''Redline Shockproof Heavy recommended''
 |}